How to Use a Non-Spill Straw Lid on Kids' Bottles
By folk berlin | Published: 2026-11-04
Category: 사용 방법 가이드
A step-by-step guide to fitting, using, and cleaning a non-spill straw lid for kids, with practical checkpoints for leaks, airflow, and dishwasher care.
Quick answer
Press the lid firmly onto a compatible bottle until the rim sits flush, then open the spout before drinking. After each use, rinse the straw and lid, and run them through the dishwasher only up to 40°C to keep the seal working.
Why fit and airflow matter more than the lid alone
A non-spill straw lid only works as well as its seal and vent. If the lid is not pushed down evenly, liquid can seep around the rim even when the spout is closed. If the straw or vent is blocked, kids have to suck harder, which often leads to tipping the bottle or giving up.
The Folk Berlin Non-Spill Drinking Straw Lid in Light Green is designed for Blafre stainless steel bottles in 300ml and 500ml sizes. It is not a universal lid, so check your bottle brand and neck size before assuming it will fit. The lid is made without BPA and phthalates and is dishwasher safe up to 40°C, but high heat can warp plastic and break the seal over time.
When to choose a straw lid instead of a plain cap
Straw lids suit toddlers and young kids who are transitioning from sippy cups or who tend to tip bottles too far. They also help kids drink while sitting in a stroller or car seat, where tilting a bottle is awkward. The trade-off is more parts to clean and a straw that can pinch or clog with thick drinks.
If your child mostly drinks water and is old enough to sip from an open cup, a simple cap may be easier to maintain. For milk, smoothies, or juice with pulp, expect to clean the straw more often or choose a different lid.
Step-by-step: fit, use, and clean your straw lid
- Check bottle compatibility: Confirm your bottle is a Blafre stainless steel model in 300ml or 500ml. Remove any old lid or cap and check that the bottle neck is clean and dry. If the lid does not sit flush, stop and check the model—do not force it.
- Seat the lid evenly: Press the lid down with the palm of your hand, working around the rim until it clicks or sits flat. Do not push only one side, which can leave a gap. Run a finger around the rim to feel for any raised edge before filling.
- Open the spout before drinking: Flip or slide the spout to the open position. The lid is designed to stop leaks when closed, not when open, so teach kids to open it fully before tipping. Close the spout after every drink to keep the leak-proof seal active.
- Test for airflow and leaks: Fill the bottle with water, close the spout, and turn it upside down over a sink for a few seconds. Then open the spout and take a sip to check that air flows and liquid comes through easily. If water drips when closed, reseat the lid; if sipping is hard, rinse the straw and vent.
- Clean after each use: Rinse the lid and straw under warm running water, then wash with mild soap and a small brush. Place parts in the dishwasher only on a cycle at or below 40°C. Skip the high-heat drying cycle—air-dry parts fully before reassembling.
- Store dry and reassembled loosely: Let the lid and straw dry completely, then store them with the spout open so air can circulate. Do not store the bottle sealed with liquid inside for long periods. A dry lid smells fresher and seals better next time.
Product facts
- Non-Spill Drinking Straw Lid, Light Green: Fits Blafre stainless steel drinking bottles in 300ml and 500ml sizes. Check your bottle model before buying, because this lid is not a universal fit.
Non-Spill Drinking Straw Lid, Light Green - Non-Spill Drinking Straw Lid, Light Green: Made of sturdy plastic that is BPA- and phthalate-free. You can feel confident using it for daily drinks, but it is still plastic, so avoid very hot liquids.
- Non-Spill Drinking Straw Lid, Light Green: Dishwasher safe up to 40°C. Use a low-temperature or delicate cycle to protect the seal and avoid warping.
